| Parameter: | Group: | Used in/Using parameters (direct dependence): | Where would the design resize when I change the parameter expression: |
| A | Main |
Used In: B (Main) TW1, ArcH (Irregular Panel) SBHW (Snap Lock) |
Length of the box |
| B | Main |
Used In: IPH (Irregular Panel) FH (Flap) PH (Flaps) DySEB, TH, DySTB, SBH1 (Snap Lock) Using: A (Main) |
Width of the box |
| H | Main | - | Height |
| GLC | Main | - | Correction because of the glue flap |
| UL | Main |
Used In: IPC (Irregular Panel) STH (Snap Lock) |
Defines if layers should be used |
| LSC | Layers |
Used In: IPC (Irregular Panel) STH (Snap Lock) |
Layer step crease |
| STLL | Layers |
Used In: STH (Snap Lock) |
Snap tuck layer level |
| IPH | Irregular Panel |
Used In: IPH1, TH1 (Irregular Panel) Using: B (Main) |
- |
| IPC1 | Irregular Panel | - | Irregular panel correction |
| IPC2 | Irregular Panel | - | Irregular panel correction |
| IPH1 | Irregular Panel |
Used In: TH1 (Irregular Panel) Using: IPH (Irregular Panel) |
Irregular panel height |
| TW1 | Irregular Panel |
Used In: FR (Irregular Panel) Using: A (Main) |
- |
| TH1 | Irregular Panel |
Used In: FR (Irregular Panel) Using: IPH, IPH1 (Irregular Panel) |
Tongue height |
| FR | Irregular Panel |
Using: TW1, TH1 (Irregular Panel) |
Fillet Radius |
| ArcH (A55.40.01.03.a) | Irregular Panel |
Using: A (Main) |
Arc height |
| IPC (A55.40.01.03.a) | Irregular Panel |
Using: UL (Main) LSC (Layers) |
- |
| FH (A55.40.01.03.a) | Flap |
Used In: R (Flap) Using: B (Main) |
Flap height |
| R (A55.40.01.03.a) | Flap |
Using: FH (Flap) |
Radius |
| DxFT (A55.40.01.03.a) | Flap |
Used In: DyFT (Flap) |
Horizontal Size of Flap Taper |
| DyFT (A55.40.01.03.a) | Flap |
Using: DxFT (Flap) |
Vertical Size of Flap Taper |
| PH (A55.40.01.03) | Flaps |
Used In: TEH (Tuck End) Using: B (Main) |
Panel Height |
| PC1 (A55.40.01.03) | Flaps | - | Panel correction |
| TEH (A55.40.01.03) | Tuck End |
Used In: TER (Tuck End) Using: PH (Flaps) |
Tuck end height |
| TER (A55.40.01.03) | Tuck End |
Using: TEH (Tuck End) |
Tuck end radius |
| DySEB | Snap Lock |
Used In: SBHW, calc, SED (Snap Lock) Using: B (Main) |
Vertical size of the Snap End bevel |
| SBHW | Snap Lock |
Used In: TW, SED (Snap Lock) Using: A (Main) DySEB (Snap Lock) |
Snap Bottom hole width |
| TW | Snap Lock |
Used In: STFR (Snap Lock) Using: SBHW (Snap Lock) |
Tongue width |
| TH | Snap Lock |
Used In: SBH, calc, SED, STFR (Snap Lock) Using: B (Main) |
Tongue height |
| DySTB | Snap Lock |
Used In: STFR (Snap Lock) Using: B (Main) |
Vertical size of the Snap Tuck bevel |
| SBH1 | Snap Lock |
Used In: SBH, DxSEB, calc, SED (Snap Lock) Using: B (Main) |
Snap Bottom height |
| SBH | Snap Lock |
Used In: STH (Snap Lock) Using: TH, SBH1 (Snap Lock) |
Snap Bottom height |
| STH | Snap Lock |
Used In: STFR (Snap Lock) Using: UL (Main) LSC, STLL (Layers) SBH (Snap Lock) |
Snap Tuck height |
| DxSEB | Snap Lock |
Using: SBH1 (Snap Lock) |
Horizontal size of the Snap End bevel |
| SBB | Snap Lock | - | Snap Bottom width correction |
| SBB1 | Snap Lock | - | Snap bottom bevel |
| SEB | Snap Lock | - | Snap End width correction |
| SEB1 (A55.40.01.03.a) | Snap Lock | - | Snap end bevel |
| calc | Snap Lock |
Used In: SED (Snap Lock) Using: DySEB, TH, SBH1 (Snap Lock) |
- |
| SED | Snap Lock |
Used In: SEFR (Snap Lock) Using: DySEB, SBHW, TH, SBH1, calc (Snap Lock) |
Distance from catch point to Snap Lock top |
| SEA (A55.40.01.03) | Snap Lock | - | Snap end angle |
| SEFR (A55.40.01.03) | Snap Lock |
Using: SED (Snap Lock) |
- |
| STFR (A55.40.01.03) | Snap Lock |
Using: TW, TH, DySTB, STH (Snap Lock) |
- |
| GL | Glue Flap | - | Glue flap width |
| GLA | Glue Flap |
Used In: GLA1 (Glue Flap) |
Webbed flap angle |
| GLA1 | Glue Flap |
Using: GLA (Glue Flap) |
Glue flap angle |