| Parameter: | Group: | Used in/Using parameters (direct dependence): | Where would the design resize when I change the parameter expression: |
| A | Main |
Used In: B (Main) Dist (Female Cuts) PH (Panel) DxCLPB1 (Crash Lock) |
Length of the box |
| B | Main |
Used In: LFR (Locking Flap) VOFC (Female Cuts) LFH (Locking Flap) PH1 (Panel) CLFH, CB, CLPH, CLPH1 (Crash Lock) Using: A (Main) |
Width of the box |
| H | Main | - | Height |
| GLC | Main | - | Correction because of the glue flap |
| UL | Main | - | Defines if layers should be used |
| LSC | Layers | - | Layer step crease |
| LFR | Locking Flap |
Used In: DyFCB2 (Female Cuts) LFH, BO (Locking Flap) Using: B (Main) |
Locking flap radius 1 |
| DxFCB2 | Female Cuts | - | - |
| DyFCB2 | Female Cuts |
Used In: LFH (Locking Flap) Using: LFR (Locking Flap) |
- |
| VOFC | Female Cuts |
Used In: LFH (Locking Flap) Using: B (Main) |
Vertical offset of the female cut |
| Dist | Female Cuts |
Using: A (Main) |
Distance between the curve and the lock |
| LFC | Locking Flap | - | Locking flap correction |
| LFH | Locking Flap |
Used In: BO (Locking Flap) Using: B (Main) LFR (Locking Flap) DyFCB2, VOFC (Female Cuts) |
Locking Flap Height |
| BO | Locking Flap |
Using: LFR, LFH (Locking Flap) |
Length of lock on dust flap |
| PH | Panel |
Using: A (Main) |
Panel Height |
| PC1 | Panel | - | Panel correction |
| PC2 | Panel | - | Panel correction |
| PH1 | Panel |
Using: B (Main) |
Panel height |
| CLFH | Crash Lock |
Using: B (Main) |
Crash lock flap height |
| CB | Crash Lock |
Using: B (Main) |
Cut back length |
| Ext | Crash Lock | - | Extension |
| LSL | Crash Lock | - | - |
| SE | Crash Lock | - | - |
| R1 | Crash Lock |
Used In: R2, DxCLPB1 (Crash Lock) |
Radius |
| R2 | Crash Lock |
Used In: DxCLPB2 (Crash Lock) Using: R1 (Crash Lock) |
Radius |
| CLFC | Crash Lock | - | Slot width |
| CLPH | Crash Lock |
Using: B (Main) |
Crash Lock flap height |
| CLPH1 | Crash Lock |
Using: B (Main) |
Crash lock panel height |
| DxCLPB1 | Crash Lock |
Used In: DxCLPB4 (Crash Lock) Using: A (Main) R1 (Crash Lock) |
- |
| DxCLPB2 | Crash Lock |
Using: R2 (Crash Lock) |
- |
| DxCLPB3 | Crash Lock | - | - |
| DxCLPB4 | Crash Lock |
Using: DxCLPB1 (Crash Lock) |
- |
| GL | Glue Flap | - | Glue flap width |
| GLA | Glue Flap | - | Webbed flap angle |
| GLA1 | Glue Flap | - | Glue flap angle |